Spectrum ST4 Run & Gun Bundle 14:1 Motor - ST417_RG_GM_14
The ST4.3 can now additionally connect up to 3 Tilta Nucleus M motors, making this up to a 7 Axis rig. Direct Drive Motor ...
The ST4.3 can now additionally connect up to 3 Tilta Nucleus M motors, making this up to a 7 Axis rig.
This is a custom cable that runs from the Spectrum ST4's i/o port to the Nodo Inertia Wheels Receiver (RX).
Movement: ST4 - 4 axis motion controller - Pan/Tilt/Focus and Slide on Dana Dolly
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
Movement: ST4 - 4 axis motion controller - Pan/Tilt/Focus and Slide on Dana Dolly
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
The xR3ACH Waterproof cover, is our thinnest and softest cover for the xR3ACH back mount. Its inner fleece material keeps the back mount protected from anything that might rub or scratch against it.
The Winter softshell cover is a neoprene cover that keeps your xR3ACH performing at its best at sub-zero temperature (0C/32F down to -20C/-4F).
37 to 49.5 lb Load Capacity Range, Change Core for Different Weight Setup, Pre-Extended for Quick Change ...
17.5 to 31 lb Load Capacity Range - Change Core for Different Weight Setup - Pre-Extended for Quick Change ...
For Black Arm 3-Axis Stabilizer, Replacement Tilt Arm Dampener, Use for Extra Dampening
The Black Arm Tilt Dampener from FLOWCINE can be used as a replacement component in your Black Arm stabilizer ...
The Black Arm Tilt Dampener from FLOWCINE can be used as a replacement component in your Black Arm stabilizer ...
The FLOWCINE Black Arm Roll Dampener replaces the existing roll dampener of your FLOWCINE Black Arm stabilizer system.
Note: The Universal Rack ships WITHOUT the two single clamps. These needs to be purchased separately.
Shipping weight: 2.6 kg
Shipping dimensions: 30 × 10 × 11 cm
Shipping weight: 2.6 kg
Shipping dimensions: 30 × 10 × 11 cm
The Flowcine Stub mount is a small lightweight 50mm tube that you can attach through a car’s tow eye bolt or similar.
The GLINK docking station tool rack is a clean way to store your tools on the docking station.
GLINK Spring Cores ( Grey: 12.5-18.5 KG – 27.5-40.5 LBS )
The Monitor clamp for CF Ring is a quick way to attach a monitor to your gimbal setup.
The GLINK handheld mount is a telescopic mount for either hard mounted cameras and/or electronic heads such as the ARRI Trinity, MK-V Omega/AR or the Betz Wave.
The xDrop is a male to female socket block connection bracket that drops the arm connection 85mm / 3.4″.
The xPEG Rip-Tie also comes with a ⅜”-16 UNC threaded hole, if the user wishes to mount anything else on it (such as a eyebolt, for example).
A ZUD 1/4 20" male (retrofit any 1/4 20 female with Z-Release) is used to retrofit your existing articulating arm, giving you Zacuto Z-Release (quick release) action on one or both ends of the articulating arm.
The Rigid nose mount is an accessory for the times where you need to lock up the roll/tilt movement for the Black arms head. Common use cases could be when the Black is mounted on to a motorcycle ...
300mm Front extension block. For the larger frame gimbals, you may need to extend the Black a little bit.
180mm Front extension block. For the larger frame gimbals, you may need to extend the Black a little bit.
