eMotimo Spectrum ST4- Run + Gun Bundle - GM - ST417_RG_GM_DD14

Product Details

Movement : 4 unique axis of movement

Size : 7.35" x 7.3" x 5“

Weight : 4.5 lbs.

Supports : 15 lbs.

Bulb Ramping : Yes, compatible with 3rd party solutions

Pan speed : 12 inch/second

Tilt speed : 60 degrees/second

Slider speed : Up to 1 foot /second

Powering specs : 12-24V. Minimum 2A. 3.5A preferred. Connector: 2.1mm x 5.5mm x 12mm circular barrel connector – centre positive.

PLEASE NOTE: Camera is not included

eMotimo's smallest and lightest 4-axis bundle. Easy to pack and carry. Grab and go shoot.

WEIGHT TO PAYLOAD RATIO
power to portability? Strength to mass ratio? Spectrum ST4 is the strongest motion control unit for its size and weight.

INTERVIEW PING-PONG MODE
Set up a simple A-B continuous move to serve as your robotic second camera, or push it further by adding a focus module to keep your subject sharp during interviews. Set up one camera on spectrum to track your subject and use a second camera for close-ups. Add smooth dynamic movement to your interviews with almost no effort.

COMPLEX KEYFRAMES
When programming a shot on spectrum you can set up to 9 individual keyframes for your move. You set your start point and end point and can add up to 7 frames in between.

DURABLE - MACHINED TO LAST
Internal wires and heavy duty connectors are protected by the CNC-milled, aircraft-grade, aluminium chassis. Spectrum ST4 is built to last.

COMPLETELY REPEATABLE (EVEN AT HIGH SPEEDS)
The spectrum ST4 is repeatable at low and high speeds. If the ability to shoot higher end VFX matters to you, then you are in the right place. Regardless of changing source voltage, or payload, we never drift while in shot like encoded DC motors. We dont drift slow and we dont drift fast. Our passes are the same, pass after pass, enabling you to push your craft further without any mid shot wiggle to correct in post.

BETTER TIMELAPSE

• Movement: 4 unique axis of movement
• Lightweight: 4.5 lbs
• Small: 7.35" x 7.3" x 5"
• Strong: supports 15 lbs
• Bulb Ramping: Compatible with 3rd party solutions

SMOOTH BUILT-IN RAMP
For both live and programmed shots you can control your movements ramp. This means ultra-smooth starts and stops. Smooth ramp is what gives spectrum footage a natural feel.

TUNE YOUR SPECTRUM ST4 FOR BETTER LIVE CONTROL
The Spectrum ST4 is all about feel. Unlike our previous products and most other motion control on the market, the spectrum has outstanding live control through the remote. Because of this, we can live drive the head around with no jitters or unwanted movements that can show up with manual control. The spectrum ST4 is armed with 11 diffrent motor move presets from turbo mode to quiet interview mode and everything in between.

Spectrum ST4- Run + Gun Bundle - GM - ST417_RG_GM_DD14

Our smallest and lightest 4-axis bundle. Easy to pack and carry. Grab and go shoot.

WHAT'S In The Box:

1) spectrum ST4 4-axis motion control unit

2) spectrum medium hard case 

3) eMotimo Heavy Duty L-bracket (camera / Fz motor mounting)

4) eMotimo Fz (focus) Motor

5) iFootage Shark Slider with 30 inch base and 2 foot extension (configure to 2 and 4 foot lengths)

6) iFootage integration kit with motor(s) of your choosing

7) uSD Card/Instructions

8) Arca compatible plate for pan axis

9) PS4 DUALSHOCK®4 wireless controller

10) 12V AC power supply

11) CL-N3, CL-DC0, CL-S2 DSLR camera trigger cables

Hardware map

#1 Spectrum ST4: Spectrum ST4 controls and powers all 4-axis of motion at the same time.

#2 PS4 controller: The PS4 controller is included in every spectrum purchase. This control is great for wirelessly controlling 4 axis of motion precisely, intuitively, and simultaneously.

#3 Arca compatible L-brackets: To mount your camera to spectrums arca compatible tilt clamp, you will need to first mount your camera to an arca compatible L-bracket.

#4 Arca compatible clamps (ballheads, or monopod heads): Spectrums base comes with an arca plate mounted to the pan axis. You will need to lock it down by using an arca compatible clamp on your tripod or slider. For greater adjustability, mount spectrum to a ballhead or monopod head. These are great if you’ve moving up a slope on your slider and need to level spectrum, if you want to raise your spectrum up to avoid any interference, or for leveling on a tripod.

#5 Focus Fz & Integrated L-Bracket: Mount focus Fz to a 15mm rod. If you pick up our Fz + heavy duty L-bracket+ rail + clamp this is included and mounts to the end of the L-Bracket.

#6 spectrum ST4 / Dana Dolly Bundle

#7 spectrum ST4 / Shark Run & Gun Bundle: Mount your spectrum directly the the carriage on your shark slider and have spectrum control your linear motion.

#8 Tripod: Mount spectrum for panning and tilting to a tripod using an arca compatible clamp.

#9 eMotimo cart: Mount spectrum to the eMotimo cart by using a monopod head or ballhead.

Electronics map

#1 spectrum ST4

#2 Camera shutter cable: Included with a spectrum purchase and sold separately. The camera shutter cable connects from spectrums camera port to your cameras shutter port. Spectrums built-in intervalometer will send a signal to trigger your camera to fire for SMS (shoot-move-shoot) timelapse shots using this cable.

#3 PS4 controller: Your PS4 controller connects to spectrum using the bluetooth dongle. Make sure this dongle is fully inserted before connecting your remote. Extra dongles can be found here.

#4 SD card - Firmware: An SD card is included in every spectrum ST4 purchase. 

#5 Power - 12-24V: Using the included AC adapter or an external battery, power your spectrum ST4 using the following specs: 12-24V. Minimum 2A. 3.5A preferred. Connector: 2.1mm x 5.5mm x 12mm circular barrel connector – center positive.

#6 Focus Fz (M3 or M4 port): Focus Fz’s primary motor port is M4. However, you can use two Fz units with spectrum and in this configuration you can use the M3 motor port for your second Fz unit.

#7 Slider: Your slider’s primary motor port is M3.

#8 Cart: Your cart’s primary motor port is M3.

#9 Turntable: Your turntable’s primary motor port is M3.

#10 External trigger: The spectrum’s i/o port is used for like external triggering or serial communication to external devices.

#11 future: USB port – future functionality – Powering the spectrum for motor moves from any USB port is not supported.