usable with FGS-900045 Heavy Duty Stand from Steadicam ....
The Black T-nut is a clever M12x1.75 nut for tool less or 19mm wrench tightening.
The Black Arm Vertical Dampener from FLOWCINE can be used as a replacement component in your Black Arm stabilizer, or for increased dampening when traveling over rough terrain or when supporting a heavier rig.
für Easyrig Tragesysteme konzipiert, inklusive 4x Kugel Endstücke (2x 1/4" & 2x 3/8" Gewinde)
Protects your Stabil and Stabil G2 arm from dirt and scratches.
Sale
ED-CP198/2000S V-Mount Battery Kit with 2× DUO-C198P Battery & 1× VL-2000S Simultaneous Charger
Spectrum ST4 Run & Gun Bundle 14:1 Motor - ST417_RG_GM_14
The ST4.3 can now additionally connect up to 3 Tilta Nucleus M motors, making this up to a 7 Axis rig. Direct Drive Motor ...
The ST4.3 can now additionally connect up to 3 Tilta Nucleus M motors, making this up to a 7 Axis rig.
This is a custom cable that runs from the Spectrum ST4's i/o port to the Nodo Inertia Wheels Receiver (RX).
Movement: ST4 - 4 axis motion controller - Pan/Tilt/Focus and Slide on Dana Dolly
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
Movement: ST4 - 4 axis motion controller - Pan/Tilt/Focus and Slide on Dana Dolly
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
ST4.3 - 7 axis motion controller - Pan/Tilt/M3/M4 ports with up to 3 Tilta Nucleus M Motors.
The xR3ACH Waterproof cover, is our thinnest and softest cover for the xR3ACH back mount. Its inner fleece material keeps the back mount protected from anything that might rub or scratch against it.
The Winter softshell cover is a neoprene cover that keeps your xR3ACH performing at its best at sub-zero temperature (0C/32F down to -20C/-4F).
37 to 49.5 lb Load Capacity Range, Change Core for Different Weight Setup, Pre-Extended for Quick Change ...
17.5 to 31 lb Load Capacity Range - Change Core for Different Weight Setup - Pre-Extended for Quick Change ...
For Black Arm 3-Axis Stabilizer, Replacement Tilt Arm Dampener, Use for Extra Dampening
The Black Arm Tilt Dampener from FLOWCINE can be used as a replacement component in your Black Arm stabilizer ...
The Black Arm Tilt Dampener from FLOWCINE can be used as a replacement component in your Black Arm stabilizer ...
The FLOWCINE Black Arm Roll Dampener replaces the existing roll dampener of your FLOWCINE Black Arm stabilizer system.
The Universal Rack clamps on to the tow bar of your car. It allows two Pro Clamp singles to be attached for further mounting of standard 48-51mm tubes. The Universal Rack is very easy to attach, and mounts on to any standard 50mm tow bar.
The Flowcine Stub mount is a small lightweight 50mm tube that you can attach through a car’s tow eye bolt or similar.
The GLINK docking station tool rack is a clean way to store your tools on the docking station.
GLINK Spring Cores ( Grey: 12.5-18.5 KG – 27.5-40.5 LBS )
The Monitor clamp for CF Ring is a quick way to attach a monitor to your gimbal setup.
The GLINK handheld mount is a telescopic mount for either hard mounted cameras and/or electronic heads such as the ARRI Trinity, MK-V Omega/AR or the Betz Wave.
